Teejet GuideLine SmartPad II Manual do Utilizador Página 89
- Página / 198
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SmartPad II
Software Version 4.02
Chapter 3 - Real-Time Guidance 3-35
Lightbar Setup
Alarm
The Alarm menu configures operator warnings that can be shown on the lightbar text display when approaching pre-
mapped hazards and previously applied areas. Alarm settings are Off, Applied Area, Hazard and All. Each feature is
described below in more detail, see Table 3-16. This menu item is used in conjunction with the Hazard Range menu
item found on page 3-37. Hazard Range is used to define how far in advance of the hazard you will be notified.
To change the Alarm setting; highlight the Alarm menu item and press . The Alarm dialog box will appear. Select
the desired setting using the arrow keys , once the desired setting is selected, press to return back to the
Lightbar setup menu, see Figure 3-44.
Using the Alarm Setting to Detect a Previously Applied Area
The Alarm menu item allows you to detect when the vehicle has entered a previously sprayed area. If the Alarm menu
item is set to Applied Area or All, any area you spread or spray, including headlands will be considered a previously
applied area. Once you enter a previously applied area the Red stop light on the Lightbar will illuminate. If you have
status detect connected and spray is on, the Alarm in the SmartPad will also sound. When you exit an applied area the
Red light will switch to the Green light,
Figure 3-44: The Alarm Menu Item
Setting Description
Off User will not be notified of any Hazards or previously sprayed areas.
Applied Area User will be notified when entering a previously applied area, see Figure 3-45. Lightbar
will display APPLIED.
Hazard User will be notified when approaching an previously mapped hazard. Lightbar will
display the name of the Hazard if named, otherwise displays HAZARD. See Figure 3-
46.
All User will be notified when approaching hazards and when they have entered a previ-
ously applied areas.
Table 3-16: Lightbar Alarm Options
- USER GUIDE 1
- Copyrights 2
- Trademarks 2
- Limitation of Liability 2
- Table of Contents 3
- Chapter 1 - Introduction 9
- Welcome to SmartPad II 10
- What’s New in Version 4.02 12
- Figure 1-1: 13
- Unpacking Your System 14
- Installing Your System 14
- GPS Receiver 14
- GPS Antenna 15
- Lightbar 15
- Lightbar 17
- Interface Cable 17
- GPS Receiver Compatibility 17
- Chapter 1 Notes 22
- Chapter 2 - Software Overview 23
- SmartPad II Software Overview 24
- SmartPad II Keys 25
- Screen Selection 26
- Data Entry 26
- Menu Pages 26
- Dialog Boxes 27
- First Time Setup Process 29
- SmartPad II Main Launcher 30
- Launching an Application 31
- Main Setup 32
- Communications Setup 33
- Setting Description 34
- Port Stop Bits 36
- SmartPad II Setup 38
- Display Brightness 39
- System Setup 41
- Language 43
- SmartPad II Tools 46
- Receiver Status 47
- GPS Logger 48
- Figure 2-27: Lightbar Test 49
- Delete Files 50
- Set Date and Time 51
- Chapter 2 Notes 53
- Guidance Setup 57
- Time Start Up 58
- Swath Width 59
- Look Ahead 60
- Direction to Swath 61
- Distance to Swath 62
- Status Detect 63
- GPS Type 65
- GPS Data Rate 66
- As Applied 69
- Map Object 71
- Data Examples 72
- Time Start up 79
- Drive Sensitivity 81
- Display Mode 82
- Parallel MSG 1 84
- Parallel MSG 2 85
- Parallel MSG 3 86
- Curved MSG 87
- Hazard Range 91
- Starting Real-Time Guidance 92
- SmartPad II View Page Buttons 94
- Figure 3-51: Solid View 95
- Figure 3-52: Spray Boom View 95
- Figure 3-53: Zoom Pan Mode 96
- Figure 3-54: North Up View 97
- Figure 3-55: COG View 97
- Guidance Application Modes 98
- The Parallel Guidance Mode 99
- Mark Point B 100
- Turning On Applied Swath 101
- Exiting Real-Time Guidance 101
- The Curved A-B Guidance Mode 102
- The Curved Guidance Mode 104
- SmartPad II 106
- Software Version 4.02 106
- Marking Point A 109
- Marking Point B 110
- Circle Guideline Guidance 110
- Applied Area Detection 116
- Detecting Neighboring Swath 117
- Creating a Field Boundary 118
- Mapping Points and Hazards 121
- Marking a Named Point 122
- Marking a Hazard 123
- Marking a Named Hazard 124
- Hazard Detection 125
- Lightbar Index 127
- Lightbar State Description 128
- Chapter 3 Notes 130
- Lightbar Setup 135
- Use Lightbar 136
- LED Brightness 137
- Alarm Range 139
- Display Message 140
- Antenna Setup 141
- Setting Name Default Value 142
- Change at 1st 142
- Time start Up 142
- Offset Direction 143
- Offset Distance 144
- Data Setup 145
- Point/Grid File 147
- Boundary 148
- Background 149
- Sample Number 150
- Sample Name 151
- The Real-Time View Page 154
- Real-Time View Options 156
- Mapping a Field Boundary 157
- Dropping a Sample Point 160
- Navigating to Points 163
- Editing a Sample Point 167
- Deleting a Sample Point 168
- Chapter 4 Notes 172
- Chapter 5 - Field Mapping 173
- About the Mapper Application 174
- Fieldware for Smartpad II 184
- Real-Time View Buttons 186
- Mapper Application Modes 192
- The Polygon Stream Mode 193
- The Polygon Mark Mode 194
- The Polyline Stream Mode 195
- The Polyline Mark Mode 196
- Chapter 5 Notes 197
Manuais e produtos relacionados com Computadores Teejet GuideLine SmartPad II
Computadores Teejet RMS Office Manual do Utilizador
(120 páginas)
(120 páginas)
Computadores Teejet RX370p Manual do Utilizador
(24 páginas)
(24 páginas)
Computadores Teejet RX 400p Manual do Utilizador
(151 páginas)
(151 páginas)
Computadores Teejet LH665 VRT Manual do Utilizador
(72 páginas)
(72 páginas)
(10 páginas)
Computadores Teejet LH 500 Manual do Utilizador
(16 páginas)
(16 páginas)
IKEA OV14 002-451-73 manuály
Uživatelské manuály a uživatelské příručky pro ne IKEA OV14 002-451-73.
Poskytujeme 1 manuály pdf IKEA OV14 002-451-73 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais