Teejet TASC-6100 Manual do Utilizador Página 37
- Página / 86
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
2-21
98-05018
R2
CE & StandardVersion
TASC 6100
Setup
& Cal.
tion of the fan (spinner) must be entered using the
following procedure:
A. Set the console to the following positions;
1. Power ON
2. Mode Selector SET- UP
3. Display Selector Fan RPM
The current Fan Calibration number is displayed.
B. Use the INC./DEC. switch to set this number to the
desired value.
RATE SENSOR CALIBRATION
Calculating The Initial Rate Sensor Cal. #
(Spreader Constant)
It is necessary to enter a Spreader Constant in TASC 6100
to ensure an accurate output from the conveyor. The
spreader constant represents the number of sensor pulses
per cubic foot of material discharged. The constant is
different for different gate settings on adjustable spread-
ers. Constants relating to particular gate settings should
be calibrated and recorded for the spreader.
Calculation of the initial spreader constant requires the
following information:
1) Gate height (H) and width (W) in inches
2) Number of sensor pulses for each revolution of the
spreader rate sensor (P)
3) The distance the conveyor moves during one
revolution of the spreader rate sensor (D), in inches.
Calculate the initial spreader constant as follows:
Where: Ft
3
r
is the volume discharged during each
revolution of the spreader rate sensor, in Cubic Feet.
Continue as follows:
DISPLAY SELECTOR
Speed
Area Impl. Width
Distance
Test
Speed
PSI/Prime
Total Applied
Application Rate
OFF SET- UP DEC.
ON
OPERATE INC.
Scan
Product Vol.
Fan RPM
BOOMS
123456789
% Rate
A-2
B
A-3
A-1
D x W x H
1728
= Ft
3
r
P
Ft
3
r
= Initial Calibration Number (Spreader Constant)
- TASC-6100 1
- CHANGE LOG 2
- ABLE OF CONTENTS 3
- 98-05018 5
- TASC 6100 5
- CE & STANDARD VERSION 5
- HOW TO USE THIS MANUAL 6
- POWER SWITCH 7
- MODE SELECTOR SWITCH 7
- INC / DEC SWITCH 8
- RATE SWITCH 8
- DISPLAY SELECTOR SWITCH 8
- Switches 11
- & Cont 11
- IMPLEMENT STATUS INPUT 12
- OPERATE 14
- CHAPTER 2 CALIBRATION 17
- CHANGING UNITS 18
- Alternate Rate 19
- SETTING THE % RATE CHANGE 19
- SETTING APPLICATION RATES 19
- Standard Rate 19
- SETTING BOOM WIDTHS 20
- & Cal 21
- 123456789 22
- CONTROL VALVE 23
- Implement Status Switch 23
- All Booms Off 24
- Setting the Full Load Value 26
- Recalling the Full Load Value 26
- Low Product Alarm 27
- RESETTING ACCUMULATORS 27
- LIQUID ONLY SET-UP 28
- SETTING THE CORRECTION FACTOR 28
- FLOW SENSOR CALIBRATION 28
- TANDARD VERSION 30
- Setting The Zero Set Point 32
- Setting The High Set Point 32
- GRANULAR ONLY SET-UP 36
- SETTING THE PRODUCT DENSITY 36
- SETTING THE FAN TACH CAL. # 36
- RATE SENSOR CALIBRATION 37
- SETTING AUTO POWER DOWN TIME 40
- TANDARDVERSION 43
- Fig. 3-1. Boom Section 44
- Fig. 3-2. Changing App 45
- Rate “On The Go” 45
- Maintenance 49
- Ground Speed sensor 50
- Flow And Pressure Sensor 50
- (TOO FAST) 53
- TANDARD V ERSION 54
- RANULAR E RROR MESSAGES 57
- GROUND SPEED SENSOR FAILURE 61
- CHAPTER 6 EMERGENCY OPERATION 61
- Alt.-Rate 62
- Emergency 63
- CE & STANDARD V ERSION 66
- Appendix A 67
- TASC 6100, WIRING DIAGRAM 68
- (Flow/Pressure based) 68
- Appndx-A 69
- TASC-6100, Granular 70
- Single Conveyor 70
- Wiring Diagram 70
- FILL OUT BEFORE CALLING FOR 72
- FASTER SERVICE 72
- Appendix B 73
- Appendix B SYSTEM OVERVIEW 74
- Appndx-B 75
- Fig. B-3. Ground 76
- Speed Radar 76
- OOM INTERFACE 78
- Appendix C 81
- Appndx-C 83
- DISTANCE: _______ 86
- FLOW METER: _______ 86
Manuais e produtos relacionados com Computadores Teejet TASC-6100
Computadores Teejet TASC-6500 Manual do Utilizador
(50 páginas)
(50 páginas)
Computadores Teejet TASC-6500 Manual do Utilizador
(45 páginas)
(45 páginas)
Computadores Teejet LH 3000 Manual do Utilizador
(24 páginas)
(24 páginas)
IKEA OV14 002-451-73 manuály
Uživatelské manuály a uživatelské příručky pro ne IKEA OV14 002-451-73.
Poskytujeme 1 manuály pdf IKEA OV14 002-451-73 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais