Teejet Matrix 840G User Manual Manual do Utilizador Página 52
- Página / 58
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
www.teejet.com
86
●
Home Menu
The Home Button or Home Icon gives you
access to the unit’s three functions: Setup, Guidance
and Monitoring. The six touch screen Menu Options
(Unit Setup , Vehicle View , Field View ,
RealView Guidance , Job View and Boom
Monitoring ) quickly access all aspects of the unit.
To view the Home Menu options:
1. Press HOME BUTTON or press the screen
to activate the icons and select HOME ICON
in bottom left corner of screen.
Figure 4-15: Home Menu
Swath acres
0.00
BoomPilot
BoomPilot is used to set BoomPilot to Off/Manual
, Automatic or All On .
NOTE: GPS is unavailable when the BOOMPILOT
ICON is gray . BoomPilot status bar icon
will be Off/Manual .
NOTE: The BOOMPILOT ICON is unavailable
if a SmartCable or Section Driver Module
(SDM) is not present. To activate the boom,
a status switch must be used. Only one
Boom Section width will be illustrated and
the Status Bar will have no icon.
Guidance with SmartCable or SDM
• Turn the controller master switch to the “On”
position. The individual boom section switches
should remain in the “Off” position.
• In areas where application is not desired,
manually turn “off” the rate controller master
switch to shut off the booms. Turn the master
switch “on” to resume application.
NOTE: This does not apply unless a SmartCable or
SDM is installed on the system.
Off/Manual & Automatic
To switch BoomPilot between Off/Manual and
Automatic
1. Press BOOMPILOT ICON .
◄Off/Manual – Status Bar Icon will change to
Red
◄Automatic – Status Bar Icon will change to
Green .
All Booms On Mode
To turn all booms on
1. Press and hold BOOMPILOT ICON .
◄All On – Status Bar Icon will change to
Yellow .
Figure 4-16: Automatic to All Booms On Mode
mph acres
10.25
mph acres
10.25
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Manuais e produtos relacionados com Computadores Teejet Matrix 840G User Manual
(2 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
Computadores Teejet Matrix 430 Manual do Utilizador
(12 páginas)
(12 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais