Teejet Matrix 840G User Manual Manual do Utilizador Página 10
- Página / 67
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5
98-05188 R2www.teejet.com
Configurations
The following diagrams are reective of typical Matrix congurations. Due to the variety of possible
congurations, these should be used for reference purposes only.
Figure 1-14: Matrix w/RealView Camera
16-00022 RealView Camera
Connec t to
+12v On ly
Power Cable
45-05645
Power
Cable, 12V
45-05775
3 m Power
Cable, Battery
CAUTION CONN.
TO +12V ONLY
POWER CABLE
45-05775
DC: XXXX
8 Pos.
4 Pos.
8 Pos.
Camera
45-05617: 6 m
45-05618: 18 m
Camera Extension Cable
5 Pos.
Matrix 570G
75-30055
75-30056 w/ClearPath
Matrix 840G
75-30070
75-30071 w/ClearPath
78-50155
GPS Ant.
Kit, RAM Mount w/Suction Cup
90-02349 (Matrix 570G)
90-02700 (Matrix 840G)
Matrix
GPS
Speed
Work On-Off
78-00044 xx/xx
78-00044: 4 Pos.
78-00046: 8 Pos.
Switch Box
Work On-Off Switch
Matrix
FieldPilot
BoomPilot
Optional Accessory
Speed Out / Sense In Cable
The Speed Out / Sense In Cable assists the Matrix with two additional connections that::
►Send a radar speed signal to an external device
►Allow the user to operate the area applied function of the Matrix in series with a remote master
connection or existing apply on/off toggle in a single swath manner. However if the previous connections
are not available the supplied toggle switch allows area applied functionality without the need to connect
to a functional application implement.
Connecting to different consoles requires different adapters and calibrations.
• If connecting to TeeJet consoles use speed adapter 45-20042
◄enter calibration # 914 (#1000 in Europe) for 8xx series in RAD mode,
◄enter calibration # 9140 (#10000 in Europe) for below LH 70 Series, LH 85, 500 series, 5000,
6000, IC 24 and IC 34
• If connecting to Mid-Tech consoles no adapter is required,
◄enter calibration # 1000
• If connecting to Raven consoles use speed adapter 45-05508 (do not connect the 12v red wire
from 45-05508)
◄enter calibration # 730 in SP 2
If sensing boom shut-off for applied mapping from an existing console, attach the green wire to the valve
side of the master switch on the console. The red wire is not used.
Figure 1-15: Matrix w/8 Channel or 4 Channel VSM & Multiple RealView Cameras
POWER IN
CAN
RS-232
Power/DATA
45-05626
45-05626
Power/CAN/Data
Cable
(included with
FieldPilot kits)
3A Fuse
8 Pos.
RS-232
TJ CAN
(Terminated)
CAUTION: CONNECT
TO 12V ONLY
Power Cable
401-0016
DC: xx/xx
WARNING CONNECT
DIRECTLY TO BAT.
401-0016
Battery Adapter
45-08101
CAN Terminator
16-00022
RealView Camera
78-08067
Video Selector Module,
4CH Video CAN
78-08068
Video Selector Module,
8CH Video CAN
4 Pos.
8 Pos.
Camera
45-05617: 6 m
45-05618: 18 m
Camera Extension Cable
5 Pos.
Matrix 570G
75-30055
75-30056 w/ClearPath
Matrix 840G
75-30070
75-30071 w/ClearPath
78-50155
GPS Ant.
Kit, RAM Mount w/Suction Cup
90-02349 (Matrix 570G)
90-02700 (Matrix 840G)
Matrix
GPS
Speed
Work On-Off
78-00044 xx/xx
78-00044: 4 Pos.
78-00046: 8 Pos.
Switch Box
Work On-Off Switch
45-05786: 6 m
45-05787: 9 m
Antenna Cable
78-50187
Optional RXA-30 GPS Antenna
65-05226
Kit, Bracket
RXA-30 Antenna
Matrix
FieldPilot
BoomPilot
Optional Accessory
- U s E R M A N U A L 1
- Table of Contents 2
- CHAPTER 1– PRODUCT OVERVIEW 6
- SYSTEM FEATURES 6
- SYSTEM COMPONENTS 6
- Matrix 570G Console 6
- RealView Camera 7
- Matrix 840G Console 7
- Video Selector Modules 8
- GPS Antennas 8
- Configurations 10
- Engage/Disengage 11
- Power on/off 12
- Start Up Sequence 13
- GENERAL OPERATION INFORMATION 13
- 98-05188 R2www.teejet.com 14
- Page Layout and Navigation 15
- Home Menu 16
- CHAPTER 2 – UNIT SETUP 16
- SYSTEM SETUP 17
- Lightbar 17
- Display Mode 18
- LED Brightness 18
- Language 19
- Time Zone 20
- GPS Type 20
- GPS Port 21
- GPS Status 21
- GGA Requirements 22
- TSLIB calibration utility 23
- Touch crosshair to calibrate 23
- Screenshot 24
- Enable/Disable 24
- Capture an Image 25
- About/Save 25
- Save About Information 25
- Eight Channel VSM 26
- BOOMPILOT/SINGLE BOOM SETUP 27
- BoomPilot Setup 27
- Delay On 28
- Delay Off 29
- Number of Boom Sections 29
- Boom Section Width 29
- Single Boom Setup 30
- VEHICLE SETUP 30
- Vehicle Type 31
- Antenna Height 31
- Direction to Boom 31
- TILT GYRO MODULE SETUP 32
- Level Tilt Position 1 33
- Level Tilt Position 2 33
- Tilt Calibration Complete 33
- Tilt Correction Off 33
- FIELDPILOT SETUP 34
- Autosteer 34
- Valve Setup 35
- Cycle Left 36
- Cycle Right 36
- Maximum Duty Cycle 36
- Valve Test 37
- Con gure FieldPilot 37
- Coarse Steering Adjustment 38
- Fine Steering Adjustment 38
- Deadband 39
- Lookahead 39
- CHAPTER 3 – GUIDANCE 40
- GUIDANCE OPERATION MODES 40
- Straight A-B Guidance 40
- Curved A-B Guidance 40
- Circle Pivot Guidance 40
- Last Pass Guidance 41
- GUIDANCE BAR & STATUS BAR 41
- Guidance Bar 41
- Status Bar 41
- 0.5314.6 42
- Vehicle View 43
- Guidance Mode Select 43
- Marking A and B Points 45
- Activate Last Pass Guidance 45
- Last Pass 45
- Create Field Boundary 45
- Zoom In/Out & Perspective 47
- BoomPilot 47
- Return to Point 49
- Zoom In/Out 50
- World View 50
- Pan Mode 50
- Guidance Over Video 52
- Steering Angle Indicator 53
- Single Camera Selection 53
- Four Channel VSM 54
- Split Camera View 55
- Guideline Adjustment 56
- CHAPTER 4 – MONITORING 57
- JOB VIEW 57
- Job Information 57
- Save Information 57
- PDF Report 58
- KML Data 58
- BOOM MONITORING 59
- Boom Monitor 59
- Menu Options 61
- Unit Setup 61
- CHAPTER 5 – APPENDIX 61
- APPENDIX A ICON REFERENCE 61
- BoomPilot/Single Boom Setup 62
- Vehicle Setup 62
- Tilt Gyro Module Setup 62
- FieldPilot Setup 62
- Commandes générales 62
- Guidance Screens 63
- Job View 64
- APPENDIX B TIME ZONES 64
Manuais e produtos relacionados com Computadores Teejet Matrix 840G User Manual
(58 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais