Teejet Matrix 840G User Manual Manual do Utilizador Página 60
- Página / 67
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
●
56
BoomPilot is Unavailable
If a SmartCable or Section Driver Module (SDM) is not present, a
status switch must be used. Only one section will be illustrated, the
BOOMPILOT ICON
will be unavailable and the Status Bar will
have no icon.
Figure 4-14: Boom Unavailable
km/h ha
0.03.3
Home Menu
The Home Button or Home Icon gives you access to the
unit’s three functions: Setup, Guidance and Monitoring. The six
touch screen Menu Options (Unit Setup , Vehicle View ,
Field View , RealView Guidance , Job View and Boom
Monitoring ) quickly access all aspects of the unit.
To view the Home Menu options:
1. Press HOME BUTTON or press the screen to activate the
icons and select HOME ICON in bottom left corner of screen.
Figure 4-15: Home Menu
Swath ha
0.00
BoomPilot
BoomPilot is used to set BoomPilot to Off/Manual , Automatic
or All On .
NOTE: GPS is unavailable when the BOOMPILOT ICON is grey .
BoomPilot status bar icon will be Off/Manual .
NOTE: The BOOMPILOT ICON is unavailable if a SmartCable or
Section Driver Module (SDM) is not present. To activate the
boom, a status switch must be used. Only one Boom Section
width will be illustrated and the Status Bar will have no icon.
Guidance with SmartCable or SDM
• Turn the controller master switch to the “On” position. The
individual boom section switches should remain in the “Off”
position.
• In areas where application is not desired, manually turn “off”
the rate controller master switch to shut off the booms. Turn the
master switch “on” to resume application.
NOTE: This does not apply unless a SmartCable or SDM is installed
on the system.
Off/Manual & Automatic
To switch BoomPilot between Off/Manual and Automatic
1. Press BOOMPILOT ICON
.
◄Off/Manual – Status Bar Icon will change to Red
◄Automatic – Status Bar Icon will change to Green .
All Booms On Mode
To turn all booms on
1. Press and hold BOOMPILOT ICON .◄All On – Status Bar
Icon will change to Yellow .
Figure 4-16: Automatic to All Booms On Mode
km/h ha
10.25
km/h ha
10.25
- U s E R M A N U A L 1
- Table of Contents 2
- CHAPTER 1– PRODUCT OVERVIEW 6
- SYSTEM FEATURES 6
- SYSTEM COMPONENTS 6
- Matrix 570G Console 6
- RealView Camera 7
- Matrix 840G Console 7
- Video Selector Modules 8
- GPS Antennas 8
- Configurations 10
- Engage/Disengage 11
- Power on/off 12
- Start Up Sequence 13
- GENERAL OPERATION INFORMATION 13
- 98-05188 R2www.teejet.com 14
- Page Layout and Navigation 15
- Home Menu 16
- CHAPTER 2 – UNIT SETUP 16
- SYSTEM SETUP 17
- Lightbar 17
- Display Mode 18
- LED Brightness 18
- Language 19
- Time Zone 20
- GPS Type 20
- GPS Port 21
- GPS Status 21
- GGA Requirements 22
- TSLIB calibration utility 23
- Touch crosshair to calibrate 23
- Screenshot 24
- Enable/Disable 24
- Capture an Image 25
- About/Save 25
- Save About Information 25
- Eight Channel VSM 26
- BOOMPILOT/SINGLE BOOM SETUP 27
- BoomPilot Setup 27
- Delay On 28
- Delay Off 29
- Number of Boom Sections 29
- Boom Section Width 29
- Single Boom Setup 30
- VEHICLE SETUP 30
- Vehicle Type 31
- Antenna Height 31
- Direction to Boom 31
- TILT GYRO MODULE SETUP 32
- Level Tilt Position 1 33
- Level Tilt Position 2 33
- Tilt Calibration Complete 33
- Tilt Correction Off 33
- FIELDPILOT SETUP 34
- Autosteer 34
- Valve Setup 35
- Cycle Left 36
- Cycle Right 36
- Maximum Duty Cycle 36
- Valve Test 37
- Con gure FieldPilot 37
- Coarse Steering Adjustment 38
- Fine Steering Adjustment 38
- Deadband 39
- Lookahead 39
- CHAPTER 3 – GUIDANCE 40
- GUIDANCE OPERATION MODES 40
- Straight A-B Guidance 40
- Curved A-B Guidance 40
- Circle Pivot Guidance 40
- Last Pass Guidance 41
- GUIDANCE BAR & STATUS BAR 41
- Guidance Bar 41
- Status Bar 41
- 0.5314.6 42
- Vehicle View 43
- Guidance Mode Select 43
- Marking A and B Points 45
- Activate Last Pass Guidance 45
- Last Pass 45
- Create Field Boundary 45
- Zoom In/Out & Perspective 47
- BoomPilot 47
- Return to Point 49
- Zoom In/Out 50
- World View 50
- Pan Mode 50
- Guidance Over Video 52
- Steering Angle Indicator 53
- Single Camera Selection 53
- Four Channel VSM 54
- Split Camera View 55
- Guideline Adjustment 56
- CHAPTER 4 – MONITORING 57
- JOB VIEW 57
- Job Information 57
- Save Information 57
- PDF Report 58
- KML Data 58
- BOOM MONITORING 59
- Boom Monitor 59
- Menu Options 61
- Unit Setup 61
- CHAPTER 5 – APPENDIX 61
- APPENDIX A ICON REFERENCE 61
- BoomPilot/Single Boom Setup 62
- Vehicle Setup 62
- Tilt Gyro Module Setup 62
- FieldPilot Setup 62
- Commandes générales 62
- Guidance Screens 63
- Job View 64
- APPENDIX B TIME ZONES 64
Manuais e produtos relacionados com Computadores Teejet Matrix 840G User Manual
(58 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.535 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais